Temporary electrical installations are one of the most overlooked hazards on a UK construction site. The lighting, the distribution boards, the trailing leads, the site cabin supply — it all gets rigged quickly at the start of a job and often forgotten until something trips, sparks or shocks someone. By then the damage is done.
Electricity on a wet, muddy, constantly changing site behaves very differently from electricity in a finished building. Cables get dragged over sharp edges, boards get rained on, and plant reverses over leads. This guide covers what you actually need to get right: reduced voltage, RCD protection, cable management and the inspection regime that keeps it all safe through the life of the job.
Why site electrics are higher risk
A construction site combines everything electricity hates: water, metalwork, abrasion, vibration and people who aren't electricians plugging things in. A nick in a 230V cable lying in a puddle can be fatal. That's why the industry standard — reinforced by HSE guidance and BS 7671 — is to design out the risk at the supply, not rely on everyone being careful.
The two big principles are reduced voltage and automatic disconnection. Get those right and you've dealt with most of the serious risk before anyone picks up a drill.
110V reduced voltage: the site standard
For portable tools and task lighting on construction sites, the accepted UK standard is a 110V centre-tapped-to-earth (CTE) supply. The transformer splits the voltage so that, in a fault, the maximum voltage to earth is only 55V — far less likely to cause a fatal shock than 230V.
In practice:
- 110V (yellow) for portable hand tools, transformers and festoon lighting — the default on most sites.
- 230V (blue) should be avoided for hand tools wherever 110V is reasonably practicable. Where 230V is unavoidable, it must be protected by a 30mA RCD.
- 400V (red) for larger plant and distribution, by competent persons only.
Colour-coded plugs and sockets make it hard to connect the wrong voltage by mistake. Don't let anyone bodge a 230V tool onto a site supply with an adaptor — that defeats the whole point.
RCDs and disconnection
A residual current device (RCD) cuts the supply fast when it detects current leaking to earth — for example, through a person. For socket outlets and 230V equipment, a 30mA RCD is the standard protection. RCDs must be tested regularly using the test button, and the test recorded; they're a safety device, not fit-and-forget.
If you're drafting the controls for a job, an electrical contractor risk assessment template is the right place to capture reduced voltage, RCD protection and isolation arrangements.
Cable management: the everyday killer
Most site electrical incidents aren't exotic — they're damaged cables and leads run across access routes. Practical controls:
- Route cables at high level on hooks or catenary wires, away from traffic and water.
- Protect any cable that must cross a route with proper cable ramps, not scaffold boards.
- Inspect leads before use for cuts, exposed conductors and damaged plugs — this is a perfect daily toolbox talk topic.
- Never run cables through standing water or coil them tightly while in use.
- Take damaged leads out of service immediately — quarantine, don't just leave them in the pile.
Overhead and buried services
Temporary installations aren't the only electrical risk on site. Overhead power lines and buried cables cause some of the most serious incidents in construction. If your work involves plant near overhead lines, or any excavation, those hazards need their own controls — a permit to dig for digging, and strict exclusion zones for overhead lines.
Who can work on it, and inspection
Temporary electrical installations must be designed, installed, inspected and maintained by competent persons — in most cases a qualified electrician. On larger sites a competent person should be appointed to manage the installation.
A typical inspection regime looks like:
- Daily/visual: users check leads, plugs and RCD test buttons before use.
- Weekly/monthly: competent person inspects distribution boards, transformers and fixed wiring; records findings.
- Formal inspection and test: of the temporary installation at suitable intervals (commonly every three months for construction sites under BS 7671), and after any significant change.
Keep the records. A site monitoring bundle gives you the inspection and checklist forms to evidence that this actually happened — which matters if the HSE ever asks.
Practical checklist before you energise
- Supply agreed and installed by a competent electrician.
- 110V CTE supply available for tools and task lighting.
- 30mA RCD protection on all socket outlets and any 230V equipment.
- Distribution boards weatherproof and sited away from traffic and water.
- Cables routed high or protected at crossings; no bodged adaptors.
- Inspection schedule set, with records and a named competent person.
- Isolation and lock-off arrangements agreed for alterations.
FAQ
Is 110V a legal requirement on construction sites?
There's no single regulation that says "use 110V," but the Electricity at Work Regulations 1989 require you to control electrical risk so far as is reasonably practicable. Reduced voltage is the long-established, industry-accepted way of doing that for portable tools, so if you use 230V hand tools you'll need a strong justification and 30mA RCD protection.
How often should a temporary site installation be inspected and tested?
Visual checks should be daily by users and routinely by a competent person. Formal inspection and testing of the temporary installation is commonly carried out at three-monthly intervals on construction sites, plus after any significant alteration or suspected fault.
Can anyone plug in and extend the site supply?
Users can plug approved tools into existing outlets, but altering, extending or fixing the installation must be done by a competent person. Running extra outlets off makeshift extensions is exactly how installations drift into a dangerous state.
Do I still need a risk assessment if I'm only using 110V tools?
Yes. Reduced voltage controls one hazard but doesn't remove cable damage, wet conditions, overloading or working near other services. A written assessment ties the controls together and shows you've thought it through.
The bottom line
Safe site electrics come down to designing out the risk at the supply — reduced voltage, RCDs, weatherproof boards — then managing cables and inspecting properly through the job. The kit does most of the work; your job is to specify it, record it and keep it maintained.
If you want the paperwork sorted fast, the Electrician Risk Assessment Pack bundles the risk assessments, permits and monitoring forms an electrical contractor needs on site. Prefer unlimited access to every template? SafetyPod membership gives you the lot for £69/year — edit, brand and reuse across every job.